Module knobs

A family of knobs for modular-synth shafts: bore and D-flat dimensions against a stated standard, press-fit allowances, and rendered sizes.

This is a CAD spec on Spekkr, published by onyx. It is listed with the other specs. Paste the line to an agent that can open a web address, and the agent fetches the files and builds from them.

Spec
onyx/module-knobs
Version
0.2.0
Published by
onyx
Updated
15 Nov 2026

Build this spec

Build the spec at https://spekkr.com/onyx/module-knobs/start.md.

Paste this to your AI agent. It opens the address, fetches the spec's files, records your choices and builds from them. Nothing to install, no account.

Published by onyx.

What does the result look like?

Module knobs: heroModule knobs: detail

What can I customize?

Modelling tool CadQuery writes STEP and STL. OpenSCAD writes STL.
Shaft standard The documented shaft table in design.md.

Your choices go into the line you copy. Anything else is yours to edit, but it leaves the tested path.

What do I get?

  • spec.md Requirements and acceptance checks.

    Module knobs

    What this builds

    A family of knobs for a modular-synth shaft, modelled as code. The bore and an optional D-flat follow a stated standard, listed in this spec (not a vague appeal to a brand). A press-fit allowance is applied. A few sizes are rendered. No physical press or a real module is required. The product name does not use a trademarked format name in the id.

    Read spekkr.inputs.json first. diameter and height size the skirt. bore and press size the hole. standard chooses the shaft table. dflat and pointer add features. tool is the modeller.

    Out of scope

    • A real pot shaft in the checks, or a press-fit feel test.
    • A trademarked format name in the id.
    • A physical print or a shop of branded knobs.

    Requirements

    Each requirement has an id. Checks name the id they cover.

    R1. Bore and D-flat
    • For 6mm-d, the shaft is 6.0 mm, and the D-flat is 0.5 mm off a 6.0 mm circle, as in design.md. For quarter-inch, the table in the same file is used.
    • The modelled bore is shaft - press on the round, and the flat is offset accordingly, each within 0.03 mm.
    • A family of three diameters (12, 16, 20, or the input plus two neighbours) is built and measured.

    Accept when: each standard's bore and flat match the table, with the allowance, for the family of sizes.

    R2. Files and frames
    • Meshes watertight. Renders: the family, a bore section, a D-flat close-up, and a knob on a modelled shaft (the shaft is a check solid, not a bought part).
    • One command builds, measures, and writes the renders. No press, no print.

    Accept when: the command passes for both tools and both standards, and a zero-allowance / wrong-flat fixture fails the table.

    R3. Inputs
    • Numeric inputs are read from spekkr.inputs.json and must stay inside the ranges in the Inputs table in design.md.
    • A value outside a range is refused before modelling, with a message that names the key.
    • Options add or remove the features in that table. The tool swap selects CadQuery or OpenSCAD; both must meet the same numbers.

    Accept when: default and one out-of-range value are handled as above, and a second legal input set still matches the formulas in design.md.

    R4. Checks and report
    • One command builds the model at the defaults and at the person's inputs, measures it against design.md, and writes a short report.
    • A model broken on purpose, for example a wall thinner than wall, must fail the report.
    • The command exports the files this spec asks for (STL, and STEP when the tool can). No physical print is required.

    Accept when: the report says pass at the defaults and at the person's inputs, and fail on a deliberately broken model.

    Verification

    Shaft bore and D-flat dimensions are measured against a stated standard table, with a press-fit allowance applied. A family of sizes is rendered. No physical press and no real module are required. The id does not use a trademarked format name.

    Definition of done

    • Every acceptance check above runs from one command, and all pass at the person's inputs.
    • A README says how to export a size, how the shaft table is written, and that a press-fit feel is not a check.
    # Module knobs
    
    ## What this builds
    
    A family of knobs for a modular-synth shaft, modelled as code. The bore
    and an optional D-flat follow a stated standard, listed in this spec (not
    a vague appeal to a brand). A press-fit allowance is applied. A few sizes
    are rendered. No physical press or a real module is required. The product
    name does not use a trademarked format name in the id.
    
    Read `spekkr.inputs.json` first. `diameter` and `height` size the skirt.
    `bore` and `press` size the hole. `standard` chooses the shaft table.
    `dflat` and `pointer` add features. `tool` is the modeller.
    
    ## Out of scope
    
    - A real pot shaft in the checks, or a press-fit feel test.
    - A trademarked format name in the id.
    - A physical print or a shop of branded knobs.
    
    ## Requirements
    
    Each requirement has an id. Checks name the id they cover.
    
    ### R1. Bore and D-flat
    
    - For `6mm-d`, the shaft is 6.0 mm, and the D-flat is 0.5 mm off a 6.0 mm
      circle, as in `design.md`. For `quarter-inch`, the table in the same
      file is used.
    - The modelled bore is `shaft - press` on the round, and the flat is
      offset accordingly, each within 0.03 mm.
    - A family of three diameters (12, 16, 20, or the input plus two
      neighbours) is built and measured.
    
    Accept when: each standard's bore and flat match the table, with the
    allowance, for the family of sizes.
    
    ### R2. Files and frames
    
    - Meshes watertight. Renders: the family, a bore section, a D-flat
      close-up, and a knob on a modelled shaft (the shaft is a check solid,
      not a bought part).
    - One command builds, measures, and writes the renders. No press, no
      print.
    
    Accept when: the command passes for both tools and both standards, and a
    zero-allowance / wrong-flat fixture fails the table.
    
    ### R3. Inputs
    
    - Numeric inputs are read from `spekkr.inputs.json` and must stay inside
      the ranges in the Inputs table in `design.md`.
    - A value outside a range is refused before modelling, with a message that
      names the key.
    - Options add or remove the features in that table. The `tool` swap
      selects CadQuery or OpenSCAD; both must meet the same numbers.
    
    Accept when: default and one out-of-range value are handled as above, and
    a second legal input set still matches the formulas in `design.md`.
    
    ### R4. Checks and report
    
    - One command builds the model at the defaults and at the person's inputs,
      measures it against `design.md`, and writes a short report.
    - A model broken on purpose, for example a wall thinner than `wall`, must
      fail the report.
    - The command exports the files this spec asks for (STL, and STEP when the
      tool can). No physical print is required.
    
    Accept when: the report says pass at the defaults and at the person's
    inputs, and fail on a deliberately broken model.
    
    ## Verification
    
    Shaft bore and D-flat dimensions are measured against a stated standard
    table, with a press-fit allowance applied. A family of sizes is rendered.
    No physical press and no real module are required. The id does not use a
    trademarked format name.
    
    ## Definition of done
    
    - Every acceptance check above runs from one command, and all pass at the
      person's inputs.
    - A README says how to export a size, how the shaft table is written, and
      that a press-fit feel is not a check.
    

    Open spec.md as plain text

  • design.md Shaft tables, D-flat geometry, press-fit allowance, and a family of sizes.

    Design

    This file fixes the geometry. How the model's code is organised is up to you, as long as the numbers here hold.

    Tables

    6mm-d: diameter 6.0, D-flat height 5.5 (0.5 mm from the opposite tangent — the file states the exact convention). quarter-inch: 6.35 mm, D-flat as in fixtures/knob-shafts.json.

    Press

    The bore is smaller than the shaft by press on the diameter (or on the radius, as the file says; tests use the file).

    Inputs

    KeyLabelDefaultNotes
    diameterSkirt diameter, mm16From 10 to 28.
    boreShaft bore, mm6.0The round shaft, before the D-flat, from 3.0 to 6.5.
    pressPress-fit allowance, mm0.05How much tighter the bore is than the stated shaft, from 0 to 0.12.
    heightHeight, mm12From 8 to 20.
    dflatA D-flatonA flat on the bore, as in the stated standard.
    pointerA pointer lineonA mark on the skirt.
    toolModelling toolcadqueryCadQuery writes STEP and STL. OpenSCAD writes STL.
    standardShaft standard6mm-dThe documented shaft table in design.md.

    Acceptance at the defaults

    Millimetres. Default skirt diameter 12.0, height 14.0, shaft bore 6.0, D-flat and pointer on. This is an original knob family, not a branded module standard.

    QuantityValueToleranceSource
    Skirt diameter12.000.05Of the default 'round' knob
    Height14.000.05Shaft shoulder to crown
    Bore diameter6.000.02For the shaft
    D-flat depth0.500.02When dflat is on
    Pointer line width0.400.05When pointer is on

    Three shapes ship: round, knurled, and winged. Each has a documented volume within 0.5% and a bore that accepts a 6.00 mm shaft with 0.05 mm clearance. The set is one project, three STLs.

    Screenshots

    These pictures are headless OpenSCAD renders of the reference model in reference/model.scad, at the default inputs. They are not drawings of a product that has not been modelled. The first picture is the one Spekkr shows on the spec's card. A build may ship its own goldens; those goldens are of that build and do not have to match these frames pixel-for-pixel.

    FileWhat it shows
    shots/set.pngThree knobs 12 mm skirt, D-flat bore

    How to verify

    1. Build the model at the default inputs and at two other legal input sets.
    2. Measure every row of the acceptance table in this file; each must fall inside its tolerance. Use the solid itself or a mesh library on the exported STL, as design.md says for the chosen tool.
    3. Refuse at least one out-of-range input by name before modelling.
    4. Confirm each exported part is a manifold, watertight mesh, and that walls and print orientation hold where this file asks.
    5. Shaft bore and D-flat dimensions are measured against a stated standard table, with a press-fit allowance applied. A family of sizes is rendered. No physical press and no real module are required. The id does not use a trademarked format name.
    # Design
    
    This file fixes the geometry. How the model's code is organised is up to
    you, as long as the numbers here hold.
    
    ## Tables
    
    `6mm-d`: diameter 6.0, D-flat height 5.5 (0.5 mm from the opposite tangent
    — the file states the exact convention). `quarter-inch`: 6.35 mm, D-flat
    as in `fixtures/knob-shafts.json`.
    
    ## Press
    
    The bore is smaller than the shaft by `press` on the diameter (or on the
    radius, as the file says; tests use the file).
    
    ## Inputs
    
    | Key | Label | Default | Notes |
    | --- | --- | --- | --- |
    | `diameter` | Skirt diameter, mm | 16 | From 10 to 28. |
    | `bore` | Shaft bore, mm | 6.0 | The round shaft, before the D-flat, from 3.0 to 6.5. |
    | `press` | Press-fit allowance, mm | 0.05 | How much tighter the bore is than the stated shaft, from 0 to 0.12. |
    | `height` | Height, mm | 12 | From 8 to 20. |
    | `dflat` | A D-flat | on | A flat on the bore, as in the stated standard. |
    | `pointer` | A pointer line | on | A mark on the skirt. |
    | `tool` | Modelling tool | cadquery | CadQuery writes STEP and STL. OpenSCAD writes STL. |
    | `standard` | Shaft standard | 6mm-d | The documented shaft table in design.md. |
    
    ## Acceptance at the defaults
    
    Millimetres. Default skirt diameter 12.0, height 14.0, shaft bore 6.0,
    D-flat and pointer on. This is an original knob family, not a branded
    module standard.
    
    | Quantity | Value | Tolerance | Source |
    | --- | --- | --- | --- |
    | Skirt diameter | 12.00 | 0.05 | Of the default 'round' knob |
    | Height | 14.00 | 0.05 | Shaft shoulder to crown |
    | Bore diameter | 6.00 | 0.02 | For the shaft |
    | D-flat depth | 0.50 | 0.02 | When `dflat` is on |
    | Pointer line width | 0.40 | 0.05 | When `pointer` is on |
    
    Three shapes ship: round, knurled, and winged. Each has a documented
    volume within 0.5% and a bore that accepts a 6.00 mm shaft with 0.05 mm
    clearance. The set is one project, three STLs.
    
    ## Screenshots
    
    These pictures are headless OpenSCAD renders of the reference model in
    `reference/model.scad`, at the default inputs. They are not drawings of a
    product that has not been modelled. The first picture is the one Spekkr
    shows on the spec's card. A build may ship its own goldens; those goldens
    are of that build and do not have to match these frames pixel-for-pixel.
    
    | File | What it shows |
    | --- | --- |
    | `shots/set.png` | Three knobs  12 mm skirt, D-flat bore |
    
    
    ## How to verify
    
    1. Build the model at the default inputs and at two other legal input
    sets.
    
    2. Measure every row of the acceptance table in this file; each must fall
    inside its tolerance. Use the solid itself or a mesh library on the
    exported STL, as `design.md` says for the chosen tool.
    
    3. Refuse at least one out-of-range input by name before modelling.
    
    4. Confirm each exported part is a manifold, watertight mesh, and that
    walls and print orientation hold where this file asks.
    
    5. Shaft bore and D-flat dimensions are measured against a stated standard
    table, with a press-fit allowance applied. A family of sizes is rendered.
    No physical press and no real module are required. The id does not use a
    trademarked format name.
    

    Open design.md as plain text

  • tasks.md Build tasks in order, each with a check.

    Tasks

    Work in order. Finish a task's check before starting the next.

    1. Set up. Install the tool in the tool input (CadQuery or OpenSCAD) and a mesh library for the checks. Read spekkr.inputs.json into one place at the top of the model. Check: an empty or trivial model is written and read back, and the inputs are visible in that source.
    2. Bore and D-flat (R1). Build what R1. Bore and D-flat asks for, to the numbers in design.md. In particular: For 6mm-d, the shaft is 6.0 mm, and the D-flat is 0.5 mm off a 6.0 mm circle, as in design.md. For quarter-inch, the table in the same file is used. Check: the R1. Bore and D-flat acceptance checks pass.
    3. Files and frames (R2). Build what R2. Files and frames asks for, to the numbers in design.md. In particular: Meshes watertight. Renders: the family, a bore section, a D-flat close-up, and a knob on a modelled shaft (the shaft is a check solid, not a bought part). Check: the R2. Files and frames acceptance checks pass.
    4. Inputs (R3). Build what R3. Inputs asks for, to the numbers in design.md. In particular: Numeric inputs are read from spekkr.inputs.json and must stay inside the ranges in the Inputs table in design.md. Check: the R3. Inputs acceptance checks pass.
    5. Checks and report (R4). Build what R4. Checks and report asks for, to the numbers in design.md. In particular: One command builds the model at the defaults and at the person's inputs, measures it against design.md, and writes a short report. Check: the R4. Checks and report acceptance checks pass.
    6. Goldens and the report. Render the documented views of the default model. Run the one-command report at the defaults, at the person's inputs, and at one more legal set. Check: the report says pass throughout, and the rendered views are written next to the model.
    7. Finish. Write a README that says how to install what is needed, how to change the inputs, and how to run the checks. Run the one command from a clean folder. Check: every item under Definition of done in spec.md is true.
    # Tasks
    
    Work in order. Finish a task's check before starting the next.
    
    1. **Set up.** Install the tool in the `tool` input (CadQuery or OpenSCAD)
    and a mesh library for the checks. Read `spekkr.inputs.json` into one
    place at the top of the model.
       Check: an empty or trivial model is written and read back, and the
    inputs are visible in that source.
    
    2. **Bore and D-flat (R1).** Build what `R1. Bore and D-flat` asks for, to
    the numbers in `design.md`. In particular: For `6mm-d`, the shaft is 6.0
    mm, and the D-flat is 0.5 mm off a 6.0 mm circle, as in `design.md`. For
    `quarter-inch`, the table in the same file is used.
       Check: the `R1. Bore and D-flat` acceptance checks pass.
    
    3. **Files and frames (R2).** Build what `R2. Files and frames` asks for,
    to the numbers in `design.md`. In particular: Meshes watertight. Renders:
    the family, a bore section, a D-flat close-up, and a knob on a modelled
    shaft (the shaft is a check solid, not a bought part).
       Check: the `R2. Files and frames` acceptance checks pass.
    
    4. **Inputs (R3).** Build what `R3. Inputs` asks for, to the numbers in
    `design.md`. In particular: Numeric inputs are read from
    `spekkr.inputs.json` and must stay inside the ranges in the Inputs table
    in `design.md`.
       Check: the `R3. Inputs` acceptance checks pass.
    
    5. **Checks and report (R4).** Build what `R4. Checks and report` asks
    for, to the numbers in `design.md`. In particular: One command builds the
    model at the defaults and at the person's inputs, measures it against
    `design.md`, and writes a short report.
       Check: the `R4. Checks and report` acceptance checks pass.
    
    6. **Goldens and the report.** Render the documented views of the default
    model. Run the one-command report at the defaults, at the person's inputs,
    and at one more legal set.
       Check: the report says pass throughout, and the rendered views are
    written next to the model.
    
    7. **Finish.** Write a README that says how to install what is needed, how
    to change the inputs, and how to run the checks. Run the one command from
    a clean folder.
       Check: every item under Definition of done in `spec.md` is true.
    

    Open tasks.md as plain text

  • reference/model.scad A parametric OpenSCAD reference of the default model, used to make the listing pictures. A build may use CadQuery or OpenSCAD and does not have to start from this file.
  • shots/hero.png Studio hero of the default model.
  • shots/detail.png Closer studio still of a joint, pocket, or surface.

Is it for me?

Kind
CAD
Tools
CadQuery, OpenSCAD

What does it need?

Agent permissions
shell
Commands it runs
install CadQuery or OpenSCAD, whichever the tool input names install a mesh library, such as trimesh

What changed?

  • 0.2.015 Nov 2026Studio product shots from a shared Cycles rig (cyclorama, PLA materials), including a short loop when present.
  • 0.1.014 Nov 2026First version.

For agents: start.md says how to build this spec, spec.json holds everything on this page, and bundle.tar.gz holds its files.