Print-in-place prop

A print-in-place propeller: axle clearance, a rotational sweep without intersection, approximate mass balance, and renders.

This is a CAD spec on Spekkr, published by onyx. It is listed with the other specs. Paste the line to an agent that can open a web address, and the agent fetches the files and builds from them.

Spec
onyx/print-in-place-prop
Version
0.2.0
Published by
onyx
Updated
15 Nov 2026

Build this spec

Build the spec at https://spekkr.com/onyx/print-in-place-prop/start.md.

Paste this to your AI agent. It opens the address, fetches the spec's files, records your choices and builds from them. Nothing to install, no account.

Published by onyx.

What does the result look like?

Print-in-place prop: heroPrint-in-place prop: detail

What can I customize?

Modelling tool CadQuery writes STEP and STL. OpenSCAD writes STL.

Your choices go into the line you copy. Anything else is yours to edit, but it leaves the tested path.

What do I get?

  • spec.md Requirements and acceptance checks.

    Print-in-place prop

    What this builds

    A propeller on an axle, designed to print in one piece, modelled as code. The axle gap is measured so the print does not weld. A rotational sweep of the blades clears the stand and the cap, with no illegal intersection. An approximate mass balance (first moments about the axis, assuming uniform density) is within a documented bound. Renders are written. Flight, thrust, and a motor are out of scope.

    Read spekkr.inputs.json first. diameter is the tip circle. gap is the axle clearance. blades is the count. hub_cap and stand add features. tool is the modeller.

    Out of scope

    • Flight, thrust, a motor, or a wind-tunnel test.
    • A physical print, or a balance on a real pin.
    • A branded propeller or a drone kit.

    Requirements

    Each requirement has an id. Checks name the id they cover.

    R1. Gap, sweep, balance
    • At rest, the axle is clear of the hub by gap within 0.05 mm, so the print does not weld.
    • A 36-step rotation about the axis shows no illegal intersection with the cap or the stand.
    • The first moments of the blade-and-hub solid about the axis, uniform density, are under the bound in design.md (near-zero imbalance).

    Accept when: the gap, the sweep, and the moments match the file.

    R2. Files and frames
    • A single print-in-place mesh (voids at the gap). Renders: rest, a mid-spin pose, a section, and the stand.
    • One command builds, sweeps, balances, and writes the renders. No flight, no print, no motor.

    Accept when: the command passes for both tools, a zero-gap input fails the weld check, and a deliberately heavy one-sided fixture fails the moment bound.

    R3. Inputs
    • Numeric inputs are read from spekkr.inputs.json and must stay inside the ranges in the Inputs table in design.md.
    • A value outside a range is refused before modelling, with a message that names the key.
    • Options add or remove the features in that table. The tool swap selects CadQuery or OpenSCAD; both must meet the same numbers.

    Accept when: default and one out-of-range value are handled as above, and a second legal input set still matches the formulas in design.md.

    R4. Checks and report
    • One command builds the model at the defaults and at the person's inputs, measures it against design.md, and writes a short report.
    • A model broken on purpose, for example a wall thinner than wall, must fail the report.
    • The command exports the files this spec asks for (STL, and STEP when the tool can). No physical print is required.

    Accept when: the report says pass at the defaults and at the person's inputs, and fail on a deliberately broken model.

    Verification

    Axle and hub clearance, a rotational sweep without illegal intersection, and approximate mass balance (moments about the axis) are checked on the model. Renders are written. Flight is out of scope. No physical print and no motor are required.

    Definition of done

    • Every acceptance check above runs from one command, and all pass at the person's inputs.
    • A README says how to export the piece, how the gap is meant to print, and that flight is not a check.
    # Print-in-place prop
    
    ## What this builds
    
    A propeller on an axle, designed to print in one piece, modelled as code.
    The axle gap is measured so the print does not weld. A rotational sweep of
    the blades clears the stand and the cap, with no illegal intersection. An
    approximate mass balance (first moments about the axis, assuming uniform
    density) is within a documented bound. Renders are written. Flight,
    thrust, and a motor are out of scope.
    
    Read `spekkr.inputs.json` first. `diameter` is the tip circle. `gap` is
    the axle clearance. `blades` is the count. `hub_cap` and `stand` add
    features. `tool` is the modeller.
    
    ## Out of scope
    
    - Flight, thrust, a motor, or a wind-tunnel test.
    - A physical print, or a balance on a real pin.
    - A branded propeller or a drone kit.
    
    ## Requirements
    
    Each requirement has an id. Checks name the id they cover.
    
    ### R1. Gap, sweep, balance
    
    - At rest, the axle is clear of the hub by `gap` within 0.05 mm, so the
      print does not weld.
    - A 36-step rotation about the axis shows no illegal intersection with the
      cap or the stand.
    - The first moments of the blade-and-hub solid about the axis, uniform
      density, are under the bound in `design.md` (near-zero imbalance).
    
    Accept when: the gap, the sweep, and the moments match the file.
    
    ### R2. Files and frames
    
    - A single print-in-place mesh (voids at the gap). Renders: rest, a
      mid-spin pose, a section, and the stand.
    - One command builds, sweeps, balances, and writes the renders. No flight,
      no print, no motor.
    
    Accept when: the command passes for both tools, a zero-gap input fails the
    weld check, and a deliberately heavy one-sided fixture fails the moment
    bound.
    
    ### R3. Inputs
    
    - Numeric inputs are read from `spekkr.inputs.json` and must stay inside
      the ranges in the Inputs table in `design.md`.
    - A value outside a range is refused before modelling, with a message that
      names the key.
    - Options add or remove the features in that table. The `tool` swap
      selects CadQuery or OpenSCAD; both must meet the same numbers.
    
    Accept when: default and one out-of-range value are handled as above, and
    a second legal input set still matches the formulas in `design.md`.
    
    ### R4. Checks and report
    
    - One command builds the model at the defaults and at the person's inputs,
      measures it against `design.md`, and writes a short report.
    - A model broken on purpose, for example a wall thinner than `wall`, must
      fail the report.
    - The command exports the files this spec asks for (STL, and STEP when the
      tool can). No physical print is required.
    
    Accept when: the report says pass at the defaults and at the person's
    inputs, and fail on a deliberately broken model.
    
    ## Verification
    
    Axle and hub clearance, a rotational sweep without illegal intersection,
    and approximate mass balance (moments about the axis) are checked on the
    model. Renders are written. Flight is out of scope. No physical print and
    no motor are required.
    
    ## Definition of done
    
    - Every acceptance check above runs from one command, and all pass at the
      person's inputs.
    - A README says how to export the piece, how the gap is meant to print,
      and that flight is not a check.
    

    Open spec.md as plain text

  • design.md Axle gap, the rotational sweep, and the mass-moment bound.

    Design

    This file fixes the geometry. How the model's code is organised is up to you, as long as the numbers here hold.

    Balance

    Assuming density 1, the vector of first moments about the axis, divided by mass and by diameter, is under 0.01 (a 1% relative offset), as in fixtures/prop-balance.json.

    Sweep

    36 steps of 10 degrees. Allowed contact is only the axle journal, at clearance gap.

    Inputs

    KeyLabelDefaultNotes
    diameterDiameter, mm80From 40 to 140, the blade tip circle.
    gapAxle gap, mm0.3From 0.2 to 0.5, the print-in-place clearance.
    bladesBlade count32, 3 or 4.
    hub_capA hub caponA print-in-place cap over the axle.
    standA small standonA stand the prop can spin on, in a desktop model.
    toolModelling toolcadqueryCadQuery writes STEP and STL. OpenSCAD writes STL.

    Acceptance at the defaults

    Millimetres. Default diameter 120, blade count 3, hub bore 8, hub cap and stand on. The blades and hub are one print-in-place part.

    QuantityValueToleranceSource
    Prop diameter120.000.20Tip to tip
    Blade count30Evenly spaced
    Print-in-place axle gap0.300.02Hub to axle
    Hub bore8.000.05If the stand pin is used
    Stand pin height20.000.10When stand is on

    A kinematics check spins the prop 360 degrees about the axle with no intersection except the documented gap. The part is printable as a single piece on its back face, blades flat. This is a display model, not a flying prop; no balance or thrust claim is made.

    Screenshots

    These pictures are headless OpenSCAD renders of the reference model in reference/model.scad, at the default inputs. They are not drawings of a product that has not been modelled. The first picture is the one Spekkr shows on the spec's card. A build may ship its own goldens; those goldens are of that build and do not have to match these frames pixel-for-pixel.

    FileWhat it shows
    shots/on-stand.pngProp 120 mm, three blades, on stand

    How to verify

    1. Build the model at the default inputs and at two other legal input sets.
    2. Measure every row of the acceptance table in this file; each must fall inside its tolerance. Use the solid itself or a mesh library on the exported STL, as design.md says for the chosen tool.
    3. Refuse at least one out-of-range input by name before modelling.
    4. Confirm each exported part is a manifold, watertight mesh, and that walls and print orientation hold where this file asks.
    5. Axle and hub clearance, a rotational sweep without illegal intersection, and approximate mass balance (moments about the axis) are checked on the model. Renders are written. Flight is out of scope. No physical print and no motor are required.
    # Design
    
    This file fixes the geometry. How the model's code is organised is up to
    you, as long as the numbers here hold.
    
    ## Balance
    
    Assuming density 1, the vector of first moments about the axis, divided by
    mass and by `diameter`, is under 0.01 (a 1% relative offset), as in
    `fixtures/prop-balance.json`.
    
    ## Sweep
    
    36 steps of 10 degrees. Allowed contact is only the axle journal, at
    clearance `gap`.
    
    ## Inputs
    
    | Key | Label | Default | Notes |
    | --- | --- | --- | --- |
    | `diameter` | Diameter, mm | 80 | From 40 to 140, the blade tip circle. |
    | `gap` | Axle gap, mm | 0.3 | From 0.2 to 0.5, the print-in-place clearance. |
    | `blades` | Blade count | 3 | 2, 3 or 4. |
    | `hub_cap` | A hub cap | on | A print-in-place cap over the axle. |
    | `stand` | A small stand | on | A stand the prop can spin on, in a desktop model. |
    | `tool` | Modelling tool | cadquery | CadQuery writes STEP and STL. OpenSCAD writes STL. |
    
    ## Acceptance at the defaults
    
    Millimetres. Default diameter 120, blade count 3, hub bore 8, hub cap and
    stand on. The blades and hub are one print-in-place part.
    
    | Quantity | Value | Tolerance | Source |
    | --- | --- | --- | --- |
    | Prop diameter | 120.00 | 0.20 | Tip to tip |
    | Blade count | 3 | 0 | Evenly spaced |
    | Print-in-place axle gap | 0.30 | 0.02 | Hub to axle |
    | Hub bore | 8.00 | 0.05 | If the stand pin is used |
    | Stand pin height | 20.00 | 0.10 | When `stand` is on |
    
    A kinematics check spins the prop 360 degrees about the axle with no
    intersection except the documented gap. The part is printable as a single
    piece on its back face, blades flat. This is a display model, not a flying
    prop; no balance or thrust claim is made.
    
    ## Screenshots
    
    These pictures are headless OpenSCAD renders of the reference model in
    `reference/model.scad`, at the default inputs. They are not drawings of a
    product that has not been modelled. The first picture is the one Spekkr
    shows on the spec's card. A build may ship its own goldens; those goldens
    are of that build and do not have to match these frames pixel-for-pixel.
    
    | File | What it shows |
    | --- | --- |
    | `shots/on-stand.png` | Prop  120 mm, three blades, on stand |
    
    
    ## How to verify
    
    1. Build the model at the default inputs and at two other legal input
    sets.
    
    2. Measure every row of the acceptance table in this file; each must fall
    inside its tolerance. Use the solid itself or a mesh library on the
    exported STL, as `design.md` says for the chosen tool.
    
    3. Refuse at least one out-of-range input by name before modelling.
    
    4. Confirm each exported part is a manifold, watertight mesh, and that
    walls and print orientation hold where this file asks.
    
    5. Axle and hub clearance, a rotational sweep without illegal
    intersection, and approximate mass balance (moments about the axis) are
    checked on the model. Renders are written. Flight is out of scope. No
    physical print and no motor are required.
    

    Open design.md as plain text

  • tasks.md Build tasks in order, each with a check.

    Tasks

    Work in order. Finish a task's check before starting the next.

    1. Set up. Install the tool in the tool input (CadQuery or OpenSCAD) and a mesh library for the checks. Read spekkr.inputs.json into one place at the top of the model. Check: an empty or trivial model is written and read back, and the inputs are visible in that source.
    2. Gap, sweep, balance (R1). Build what R1. Gap, sweep, balance asks for, to the numbers in design.md. In particular: At rest, the axle is clear of the hub by gap within 0.05 mm, so the print does not weld. Check: the R1. Gap, sweep, balance acceptance checks pass.
    3. Files and frames (R2). Build what R2. Files and frames asks for, to the numbers in design.md. In particular: A single print-in-place mesh (voids at the gap). Renders: rest, a mid-spin pose, a section, and the stand. Check: the R2. Files and frames acceptance checks pass.
    4. Inputs (R3). Build what R3. Inputs asks for, to the numbers in design.md. In particular: Numeric inputs are read from spekkr.inputs.json and must stay inside the ranges in the Inputs table in design.md. Check: the R3. Inputs acceptance checks pass.
    5. Checks and report (R4). Build what R4. Checks and report asks for, to the numbers in design.md. In particular: One command builds the model at the defaults and at the person's inputs, measures it against design.md, and writes a short report. Check: the R4. Checks and report acceptance checks pass.
    6. Goldens and the report. Render the documented views of the default model. Run the one-command report at the defaults, at the person's inputs, and at one more legal set. Check: the report says pass throughout, and the rendered views are written next to the model.
    7. Finish. Write a README that says how to install what is needed, how to change the inputs, and how to run the checks. Run the one command from a clean folder. Check: every item under Definition of done in spec.md is true.
    # Tasks
    
    Work in order. Finish a task's check before starting the next.
    
    1. **Set up.** Install the tool in the `tool` input (CadQuery or OpenSCAD)
    and a mesh library for the checks. Read `spekkr.inputs.json` into one
    place at the top of the model.
       Check: an empty or trivial model is written and read back, and the
    inputs are visible in that source.
    
    2. **Gap, sweep, balance (R1).** Build what `R1. Gap, sweep, balance` asks
    for, to the numbers in `design.md`. In particular: At rest, the axle is
    clear of the hub by `gap` within 0.05 mm, so the print does not weld.
       Check: the `R1. Gap, sweep, balance` acceptance checks pass.
    
    3. **Files and frames (R2).** Build what `R2. Files and frames` asks for,
    to the numbers in `design.md`. In particular: A single print-in-place mesh
    (voids at the gap). Renders: rest, a mid-spin pose, a section, and the
    stand.
       Check: the `R2. Files and frames` acceptance checks pass.
    
    4. **Inputs (R3).** Build what `R3. Inputs` asks for, to the numbers in
    `design.md`. In particular: Numeric inputs are read from
    `spekkr.inputs.json` and must stay inside the ranges in the Inputs table
    in `design.md`.
       Check: the `R3. Inputs` acceptance checks pass.
    
    5. **Checks and report (R4).** Build what `R4. Checks and report` asks
    for, to the numbers in `design.md`. In particular: One command builds the
    model at the defaults and at the person's inputs, measures it against
    `design.md`, and writes a short report.
       Check: the `R4. Checks and report` acceptance checks pass.
    
    6. **Goldens and the report.** Render the documented views of the default
    model. Run the one-command report at the defaults, at the person's inputs,
    and at one more legal set.
       Check: the report says pass throughout, and the rendered views are
    written next to the model.
    
    7. **Finish.** Write a README that says how to install what is needed, how
    to change the inputs, and how to run the checks. Run the one command from
    a clean folder.
       Check: every item under Definition of done in `spec.md` is true.
    

    Open tasks.md as plain text

  • reference/model.scad A parametric OpenSCAD reference of the default model, used to make the listing pictures. A build may use CadQuery or OpenSCAD and does not have to start from this file.
  • shots/hero.png Studio hero of the default model.
  • shots/detail.png Closer studio still of a joint, pocket, or surface.

Is it for me?

Kind
CAD
Tools
CadQuery, OpenSCAD

What does it need?

Agent permissions
shell
Commands it runs
install CadQuery or OpenSCAD, whichever the tool input names install a mesh library, such as trimesh

What changed?

  • 0.2.015 Nov 2026Studio product shots from a shared Cycles rig (cyclorama, PLA materials), including a short loop when present.
  • 0.1.014 Nov 2026First version.

For agents: start.md says how to build this spec, spec.json holds everything on this page, and bundle.tar.gz holds its files.