Honeycomb wall

A honeycomb storage wall: hex pitch, hook and bin clearances, wall thickness, and a rendered mated assembly, with no print required.

This is a CAD spec on Spekkr, published by onyx. It is listed with the other specs. Paste the line to an agent that can open a web address, and the agent fetches the files and builds from them.

Spec
onyx/honeycomb-wall
Version
0.2.0
Published by
onyx
Updated
14 Nov 2026

Build this spec

Build the spec at https://spekkr.com/onyx/honeycomb-wall/start.md.

Paste this to your AI agent. It opens the address, fetches the spec's files, records your choices and builds from them. Nothing to install, no account.

Published by onyx.

What does the result look like?

Honeycomb wall: heroHoneycomb wall: detail

What can I customize?

Modelling tool CadQuery writes STEP and STL. OpenSCAD writes STL.

Your choices go into the line you copy. Anything else is yours to edit, but it leaves the tested path.

What do I get?

  • spec.md Requirements and acceptance checks.

    Honeycomb wall

    What this builds

    A wall of hexagonal cells, and a couple of accessories that seat in them: a hook and a small bin. The model is code. Pitch, wall thickness, and insertion clearances are measured on the mesh. A render shows a wall with accessories mated in place. No physical print is required.

    Read spekkr.inputs.json first. pitch, wall, rows and cols size the wall, in millimetres except the counts. hooks and bin add accessories. tool is the modeller.

    Out of scope

    • A branded wall system's exact parts, or its name in the id.
    • A particular wall-mount or a masonry fixing.
    • A physical print or a hung wall.

    Requirements

    Each requirement has an id. Checks name the id they cover.

    R1. Pitch and thickness
    • Cell centres are pitch apart on a hex grid, with the neighbour deltas in design.md. The wall's bounding box matches the formula file within 0.05 mm.
    • Cell walls are wall thick, within 0.05 mm, on a mid-edge sample.
    • A value outside the stated ranges is refused before modelling.

    Accept when: default and two other sets match the formulas, and a short-of-range input is refused.

    R2. Accessories and meshes
    • A hook and a bin, when included, seat in a cell with the insertion clearance in design.md (0.2 mm), and do not overlap the wall in the mated pose.
    • Each part is watertight, with overhangs in the print position not past 45 degrees.
    • Renders: the wall, a hook, a mated bin, and an assembly of a few accessories.

    Accept when: clearances and non-overlap hold, mesh checks pass, and the four renders are written.

    R3. Files
    • Export, a report, a twice-run hash, both tools. No physical print.

    Accept when: the command passes, and a deliberately thin wall fails the report.

    R4. Inputs
    • Numeric inputs are read from spekkr.inputs.json and must stay inside the ranges in the Inputs table in design.md.
    • A value outside a range is refused before modelling, with a message that names the key.
    • Options add or remove the features in that table. The tool swap selects CadQuery or OpenSCAD; both must meet the same numbers.

    Accept when: default and one out-of-range value are handled as above, and a second legal input set still matches the formulas in design.md.

    Verification

    Hex pitch, hook and bin insertion clearances, and wall thickness are measured on generated meshes. A rendered wall with a few accessories mated in place is written. Meshes are manifold. No physical print is required.

    Definition of done

    • Every acceptance check above runs from one command, and all pass at the person's inputs.
    • A README says how to make the wall and the accessories, and that a print is optional.
    # Honeycomb wall
    
    ## What this builds
    
    A wall of hexagonal cells, and a couple of accessories that seat in them:
    a hook and a small bin. The model is code. Pitch, wall thickness, and
    insertion clearances are measured on the mesh. A render shows a wall with
    accessories mated in place. No physical print is required.
    
    Read `spekkr.inputs.json` first. `pitch`, `wall`, `rows` and `cols` size
    the wall, in millimetres except the counts. `hooks` and `bin` add
    accessories. `tool` is the modeller.
    
    ## Out of scope
    
    - A branded wall system's exact parts, or its name in the id.
    - A particular wall-mount or a masonry fixing.
    - A physical print or a hung wall.
    
    ## Requirements
    
    Each requirement has an id. Checks name the id they cover.
    
    ### R1. Pitch and thickness
    
    - Cell centres are `pitch` apart on a hex grid, with the neighbour deltas
      in `design.md`. The wall's bounding box matches the formula file within
      0.05 mm.
    - Cell walls are `wall` thick, within 0.05 mm, on a mid-edge sample.
    - A value outside the stated ranges is refused before modelling.
    
    Accept when: default and two other sets match the formulas, and a
    short-of-range input is refused.
    
    ### R2. Accessories and meshes
    
    - A hook and a bin, when included, seat in a cell with the insertion
      clearance in `design.md` (0.2 mm), and do not overlap the wall in the
      mated pose.
    - Each part is watertight, with overhangs in the print position not past
      45 degrees.
    - Renders: the wall, a hook, a mated bin, and an assembly of a few
      accessories.
    
    Accept when: clearances and non-overlap hold, mesh checks pass, and the
    four renders are written.
    
    ### R3. Files
    
    - Export, a report, a twice-run hash, both tools. No physical print.
    
    Accept when: the command passes, and a deliberately thin wall fails the
    report.
    
    ### R4. Inputs
    
    - Numeric inputs are read from `spekkr.inputs.json` and must stay inside
      the ranges in the Inputs table in `design.md`.
    - A value outside a range is refused before modelling, with a message that
      names the key.
    - Options add or remove the features in that table. The `tool` swap
      selects CadQuery or OpenSCAD; both must meet the same numbers.
    
    Accept when: default and one out-of-range value are handled as above, and
    a second legal input set still matches the formulas in `design.md`.
    
    ## Verification
    
    Hex pitch, hook and bin insertion clearances, and wall thickness are
    measured on generated meshes. A rendered wall with a few accessories mated
    in place is written. Meshes are manifold. No physical print is required.
    
    ## Definition of done
    
    - Every acceptance check above runs from one command, and all pass at the
      person's inputs.
    - A README says how to make the wall and the accessories, and that a print
      is optional.
    

    Open spec.md as plain text

  • design.md Hex pitch, accessory clearances, and mated assembly measures.

    Design

    This file fixes the geometry. How the model's code is organised is up to you, as long as the numbers here hold.

    Hex grid

    Odd rows are offset by pitch/2 in X. Overall width and height are in fixtures/hex-wall-measures.json, with volumes and the hook/bin clearances (0.2 mm radial, 0.3 mm depth).

    Mesh checks

    Watertight, min wall wall, print position: wall flat on the back face, hook standing, bin open up.

    Inputs

    KeyLabelDefaultNotes
    pitchHex pitch, mm40Centre to centre, from 28 to 60.
    wallWall thickness, mm2.4From 1.6 to 5.
    rowsRows5From 2 to 12.
    colsColumns8From 2 to 16.
    hooksInclude a hook accessoryonA hook that seats in a cell with the documented clearance.
    binInclude a small binonA bin that seats in a cell.
    toolModelling toolcadqueryCadQuery writes STEP and STL. OpenSCAD writes STL.

    Acceptance at the defaults

    Millimetres. pitch is 40, wall is 2.4, rows is 5, cols is 8, and both accessories are on. Odd rows are offset by pitch/2 in X.

    QuantityValueToleranceSource
    Cell centre distance (pitch)40.000.05Flat-to-flat neighbours
    Wall panel thickness2.400.05wall
    Hook seating radial clearance0.200.02Hook in a cell
    Bin seating depth clearance0.300.05Bin in a cell
    Minimum wall in the mesh2.400.10Except a documented hook tip, 1.6

    Print position: the wall lies on its back face, the hook stands, the bin opens up. Each exported mesh is manifold and watertight.

    Screenshots

    These pictures are headless OpenSCAD renders of the reference model in reference/model.scad, at the default inputs. They are not drawings of a product that has not been modelled. The first picture is the one Spekkr shows on the spec's card. A build may ship its own goldens; those goldens are of that build and do not have to match these frames pixel-for-pixel.

    FileWhat it shows
    shots/wall.pngHex wall 5 × 8 cells, 40 mm pitch
    shots/assembly.pngWall with hook and bin seated

    How to verify

    1. Build the model at the default inputs and at two other legal input sets.
    2. Measure every row of the acceptance table in this file; each must fall inside its tolerance. Use the solid itself or a mesh library on the exported STL, as design.md says for the chosen tool.
    3. Refuse at least one out-of-range input by name before modelling.
    4. Confirm each exported part is a manifold, watertight mesh, and that walls and print orientation hold where this file asks.
    5. Hex pitch, hook and bin insertion clearances, and wall thickness are measured on generated meshes. A rendered wall with a few accessories mated in place is written. Meshes are manifold. No physical print is required.
    # Design
    
    This file fixes the geometry. How the model's code is organised is up to
    you, as long as the numbers here hold.
    
    ## Hex grid
    
    Odd rows are offset by `pitch/2` in X. Overall width and height are in
    `fixtures/hex-wall-measures.json`, with volumes and the hook/bin
    clearances (0.2 mm radial, 0.3 mm depth).
    
    ## Mesh checks
    
    Watertight, min wall `wall`, print position: wall flat on the back face,
    hook standing, bin open up.
    
    ## Inputs
    
    | Key | Label | Default | Notes |
    | --- | --- | --- | --- |
    | `pitch` | Hex pitch, mm | 40 | Centre to centre, from 28 to 60. |
    | `wall` | Wall thickness, mm | 2.4 | From 1.6 to 5. |
    | `rows` | Rows | 5 | From 2 to 12. |
    | `cols` | Columns | 8 | From 2 to 16. |
    | `hooks` | Include a hook accessory | on | A hook that seats in a cell with the documented clearance. |
    | `bin` | Include a small bin | on | A bin that seats in a cell. |
    | `tool` | Modelling tool | cadquery | CadQuery writes STEP and STL. OpenSCAD writes STL. |
    
    ## Acceptance at the defaults
    
    Millimetres. `pitch` is 40, `wall` is 2.4, `rows` is 5, `cols` is 8, and
    both accessories are on. Odd rows are offset by `pitch/2` in X.
    
    | Quantity | Value | Tolerance | Source |
    | --- | --- | --- | --- |
    | Cell centre distance (pitch) | 40.00 | 0.05 | Flat-to-flat neighbours |
    | Wall panel thickness | 2.40 | 0.05 | `wall` |
    | Hook seating radial clearance | 0.20 | 0.02 | Hook in a cell |
    | Bin seating depth clearance | 0.30 | 0.05 | Bin in a cell |
    | Minimum wall in the mesh | 2.40 | 0.10 | Except a documented hook tip, 1.6 |
    
    Print position: the wall lies on its back face, the hook stands, the bin
    opens up. Each exported mesh is manifold and watertight.
    
    ## Screenshots
    
    These pictures are headless OpenSCAD renders of the reference model in
    `reference/model.scad`, at the default inputs. They are not drawings of a
    product that has not been modelled. The first picture is the one Spekkr
    shows on the spec's card. A build may ship its own goldens; those goldens
    are of that build and do not have to match these frames pixel-for-pixel.
    
    | File | What it shows |
    | --- | --- |
    | `shots/wall.png` | Hex wall  5 × 8 cells, 40 mm pitch |
    | `shots/assembly.png` | Wall with hook and bin seated |
    
    
    ## How to verify
    
    1. Build the model at the default inputs and at two other legal input
    sets.
    
    2. Measure every row of the acceptance table in this file; each must fall
    inside its tolerance. Use the solid itself or a mesh library on the
    exported STL, as `design.md` says for the chosen tool.
    
    3. Refuse at least one out-of-range input by name before modelling.
    
    4. Confirm each exported part is a manifold, watertight mesh, and that
    walls and print orientation hold where this file asks.
    
    5. Hex pitch, hook and bin insertion clearances, and wall thickness are
    measured on generated meshes. A rendered wall with a few accessories mated
    in place is written. Meshes are manifold. No physical print is required.
    

    Open design.md as plain text

  • tasks.md Build tasks in order, each with a check.

    Tasks

    Work in order. Finish a task's check before starting the next.

    1. Set up. Install the tool in the tool input (CadQuery or OpenSCAD) and a mesh library for the checks. Read spekkr.inputs.json into one place at the top of the model. Check: an empty or trivial model is written and read back, and the inputs are visible in that source.
    2. Pitch and thickness (R1). Build what R1. Pitch and thickness asks for, to the numbers in design.md. In particular: Cell centres are pitch apart on a hex grid, with the neighbour deltas in design.md. The wall's bounding box matches the formula file within 0.05 mm. Check: the R1. Pitch and thickness acceptance checks pass.
    3. Accessories and meshes (R2). Build what R2. Accessories and meshes asks for, to the numbers in design.md. In particular: A hook and a bin, when included, seat in a cell with the insertion clearance in design.md (0.2 mm), and do not overlap the wall in the mated pose. Check: the R2. Accessories and meshes acceptance checks pass.
    4. Files (R3). Build what R3. Files asks for, to the numbers in design.md. In particular: Export, a report, a twice-run hash, both tools. No physical print. Check: the R3. Files acceptance checks pass.
    5. Inputs (R4). Build what R4. Inputs asks for, to the numbers in design.md. In particular: Numeric inputs are read from spekkr.inputs.json and must stay inside the ranges in the Inputs table in design.md. Check: the R4. Inputs acceptance checks pass.
    6. Goldens and the report. Render the documented views of the default model. Run the one-command report at the defaults, at the person's inputs, and at one more legal set. Check: the report says pass throughout, and the rendered views are written next to the model.
    7. Finish. Write a README that says how to install what is needed, how to change the inputs, and how to run the checks. Run the one command from a clean folder. Check: every item under Definition of done in spec.md is true.
    # Tasks
    
    Work in order. Finish a task's check before starting the next.
    
    1. **Set up.** Install the tool in the `tool` input (CadQuery or OpenSCAD)
    and a mesh library for the checks. Read `spekkr.inputs.json` into one
    place at the top of the model.
       Check: an empty or trivial model is written and read back, and the
    inputs are visible in that source.
    
    2. **Pitch and thickness (R1).** Build what `R1. Pitch and thickness` asks
    for, to the numbers in `design.md`. In particular: Cell centres are
    `pitch` apart on a hex grid, with the neighbour deltas in `design.md`. The
    wall's bounding box matches the formula file within 0.05 mm.
       Check: the `R1. Pitch and thickness` acceptance checks pass.
    
    3. **Accessories and meshes (R2).** Build what `R2. Accessories and
    meshes` asks for, to the numbers in `design.md`. In particular: A hook and
    a bin, when included, seat in a cell with the insertion clearance in
    `design.md` (0.2 mm), and do not overlap the wall in the mated pose.
       Check: the `R2. Accessories and meshes` acceptance checks pass.
    
    4. **Files (R3).** Build what `R3. Files` asks for, to the numbers in
    `design.md`. In particular: Export, a report, a twice-run hash, both
    tools. No physical print.
       Check: the `R3. Files` acceptance checks pass.
    
    5. **Inputs (R4).** Build what `R4. Inputs` asks for, to the numbers in
    `design.md`. In particular: Numeric inputs are read from
    `spekkr.inputs.json` and must stay inside the ranges in the Inputs table
    in `design.md`.
       Check: the `R4. Inputs` acceptance checks pass.
    
    6. **Goldens and the report.** Render the documented views of the default
    model. Run the one-command report at the defaults, at the person's inputs,
    and at one more legal set.
       Check: the report says pass throughout, and the rendered views are
    written next to the model.
    
    7. **Finish.** Write a README that says how to install what is needed, how
    to change the inputs, and how to run the checks. Run the one command from
    a clean folder.
       Check: every item under Definition of done in `spec.md` is true.
    

    Open tasks.md as plain text

  • reference/model.scad A parametric OpenSCAD reference of the default model, used to make the listing pictures. A build may use CadQuery or OpenSCAD and does not have to start from this file.
  • shots/hero.png Studio hero of the default model.
  • shots/detail.png Closer studio still of a joint, pocket, or surface.

Is it for me?

Kind
CAD
Tools
CadQuery, OpenSCAD

What does it need?

Agent permissions
shell
Commands it runs
install CadQuery or OpenSCAD, whichever the tool input names install a mesh library, such as trimesh

What changed?

  • 0.2.014 Nov 2026Studio product shots from a shared Cycles rig (cyclorama, PLA materials), including a short loop when present.
  • 0.1.014 Nov 2026First version.

For agents: start.md says how to build this spec, spec.json holds everything on this page, and bundle.tar.gz holds its files.